Repairing where the kicker attached to the hull

I went out in my mirror yesterday the first day on holiday after spending a while getting the boat ready.

Any way twenty yards out and the kicker pulled of the hull, so i sent back in and I tried to make a temporary job of it through the bung holes and the rope just pulled through the wood, so it looked like the timber was rotten.

So I then attached the kicker to the mast.

But looking at the replacement timber for this section it appears it goes across the hull so how is the back way to replace or repair it without my dad going mad with fibre glass as he has done on the out side of the hull.... Again...

Many thanks

Oliver

sail_and_oar's picture

Hello Oliver,

The plywood piece you described with the bung holes in it is the stowage bulkhead. It's made from 5mm marine ply but the openings on my boat (all Mirrors?) are reinforced to make it thicker. It's not a great surprise the kicker ripped it out. The bung holes weren't really meant to take this sort of load. This leads me to wonder how rotten this bulkhead really is???

Replacing the whole bulkhead is going to be a real bear of a job so we won't even entertain the idea at this stage. I think a scarf joint might be appropriate. The idea of the scarf joint is to cut out the bad bit and then chamfer the egdes where you cut to a distance of 1 inch. You then cut a piece of 5mm marine ply 1 inch bigger than the piece you cut out, chamfer the edges by an inch and glue it in to replace the missing bit.

Get a sharp (ie sharp enough to trim your fingernails with it) wood chisel and start digging. I would expect if it is rotten the bad bit will be fairly small and mainly at the bottom of the bulkhead near where the bung holes are. Chop out the bad bit and chamfer all the edges back by an inch. Try not to put the chisel through the hull. You will need to make a template of the piece you want to replace. Use thick card and scissors and transer this shape onto a piece of ply. Chamfer the edges of the ply piece so it fits in the gap and remove any remaining fibreglass tape around the repair area

Behind the bulkhead is the vertical piece under the mast steps and some little wooden battens which tie the whole thing together. If possible don't disturb these, just clean up the faces of the exposed wood with a chisel then sandpaper so the glue has something decent to stick to. use a hairdryer or hot air gun to get everything boney dry before you apply the glue.

You will need to replace the fibreglass tape which probably got chopped out when you removed the part of the bulkhead. The new tape wants to overlap the old by an inch or so. Get the whole area clean and dry.

Mix up some epoxy resin. Paint some onto all the cleaned up areas of the boat. Put plenty on the back of the new piece of ply and press it into the hole. Make sure it doesn't try to fall out while the resin is still wet. If you pro[p it in with a stick use a bit of polythene to stop the stick from getting glued to the new piece of ply. Cut a piece of fibreglass tape to replace the missing bit. Paint epoxy resin onto it so it goes clear and walk away.

The next day clean everything up with fine sandpaper and give it 3 coats of varnish.

OK a list of stuff you will need
saw
chisel
hot air gun
sandpaper
cardboard
scissors
fibreglass tape
marine grade epoxy resin
Boatbuilding grade marine ply 5 (or 6) mm
varnish
sandpaper
paint brushes

Epoxy resin is really great but you have to be careful how to use it properly. Everyone who uses it should read the gudgeon Brothers guide or a similar paper. Safety and proper mixing methods are important

http://www.westsystem.com/ss/assets/HowTo-Publications/GougeonBook%20061...

OK back to the kicker fitting. Why did it pull out? If the screws pulled from thier holes you could put bigger screws in or better still use bolts with nuts and washers on the back. Before you put the new screws/bolts in get some varnish down the holes to seal the wood up. This will seal up the wood and slow the rotting process

This sort of bodgery can extend the life of a boat vastly. I've been at it 10+ years with my Mirror. New bits of hull, gunwales, centreboard case, transom. Retaped most of the inside. Man that's one lucky boat.

Cliff

Cliff

Many thanks for that, I will see what we can do

Oliver