Hello again everyone.
I want to build a carrier to carry all the mast bits inside the boat with the flat cover on, when trailing, which I hope do more of this year after joining the DCA.
Would 2 bits of wood 4" x 1" at 4 feet long with carpet wrapped around the ends that sit flat on the side tanks be ok ?.
I would make blocks to hold all the mast bits and screw them to the cross pieces that sit on the side tanks.
Any pictures of what you guys use would be great.
Cheers. Jules
PuffinInTegel
Wed, 04/13/2016 - 12:04
Permalink
"Bridges" between the gunwales
Hello Jules,

unfortuntely I have no personal experience here, as Puffin goes on my car top. The two Mirrors on trailers I have come across in recent times had some sort of bridge structure between the gunwales, i.e. two crosswise beams with recesses into which the mast, boom, gaff and oars fitted. I cannot remember how everything was tied together or otherwise fixed down, however.
The picture below was taken in 2014. The front bridge memeber had already been dropped into the boat when I took the picture, unfortunately.
To view the full-sized picture, place the mouse pointer on the picture, click the right-hand mouse button and then select "view graphic" in the pop-up context menu (in German it says "Grafik anzeigen") -- at least that's how it works in Firefox.
I shall ask the owner of the other boat in Berlin, Eckart Wiedemann, who sailed with me last September, to take a more detailed picture or two next time he takes his boat out (provided that he uses a similar arrangement).
I would use as few screws as possible. Ratchet straps and bungy cords are usually quicker.
Cheers,
Gernot
PuffinInTegel
Fri, 04/15/2016 - 13:59
Permalink
Stern support for mast
Here's the other alternative seen in Berlin - thanks to Eckart.


There is a mast head support screwed to the transom and the foot of the mast is placed on a cushion on the bow. The other spars are placed on cushions inside the boat, I assume, and everything is lashed down under the tarpaulin. This rig has travelled at 110 km/h.
Stern :
and bow :
JPH
Sat, 04/16/2016 - 09:19
Permalink
Thanks alot for the pictures,
Thanks alot for the pictures, all food for thought. Cheers. J
mirrorpete
Sat, 04/16/2016 - 11:53
Permalink
Mast,boom and gaff carrier
I am able to place my mast, boom and gaff in the Mirror. I lay them in diagonally and lash them to the thwart.
Pete
JPH
Thu, 06/02/2016 - 23:23
Permalink
I ended up with 2x holders
I ended up with 2x holders that rest on the gunnels , the mast is in the center and slightly higher up.
This works great with the flat cover as it stops puddles forming when it rains.
Hope this is helpful to anyone making something up. :-)
francovendee
Thu, 08/17/2017 - 16:09
Permalink
Boom height
As I'm struggling to duck under the boom (bumps to prove it) I wonder what the effect of raising the boom by about 75 mm would be? I know I'd have to re-position the gooseneck and the fitting on the gaff but would it greatly effect the way the boat sails? I avoid anything over a force 3 to sail in and only on lakes. I expect it will have an effect but not sure if it would be great or small? I'm hoping someone has already tried this. Colin
David Cooper
Thu, 08/17/2017 - 19:57
Permalink
Sounds viable
I doubt it would be worth the trouble just for just a 75mm change, but you could probably go for 150mm without any drastic differences in the forces involved. I don't like the idea of making extra holes in the mast and gaff, but they'd still be strong enough. The weakest point would be the gaff jaws with the wind having greater leverage to apply force to them, but if you're avoiding strong winds they should be fine - you can always lower the mainsail and get home under jib if you're worried.
A way to reach the same end result without weakening anything would be to make a new bottom-end extension for the mast to raise it by the same distance, then add short strops to the ends of the shrouds, held by shackles (which would have tape wound round them to protect the jib). This extension to the mast would be a strong metal tube 30cm long fitting tightly round the base of the mast with the same square-section end shape underneath it to fit into the deck mount. You'd take the halyard cleats off the mast and then refit them on the tube.
Getting a tube of the right diameter and strength could be hard, but a third option would be to make a raised wooden base for the mast to sit on. It needs to have sides sloping down at 45 degrees to the deck to either side and straight ahead to stop it falling over - those would transfer the loads on down through the vertical sheets of plywood that are already there under the deck. This base would fit into the existing mast mount on the deck. To stop it toppling over towards the stern, the front part of it would need to be bolted through the deck into some new supporting blocks of wood which would themselves have to be bolted horizontally through the top of the vertical sheet of ply that runs between the two compartments under the deck so that that vertical ply can take the load. The biggest force trying to move the base of the mast sideways will come from the mainsail, and i's possible that it can produce a high sideways loading, so I would also bolt the sides of the support down to new blocks of wood under the foredeck in the same manner, those blocks again being bolted sideways into the existing vertical ply.
The two methods I've suggested will change the forestay angle very slightly, which may lead to the jib not being perfectly shaped, but it occurs to me that the new-cut jib might work well with such a raised rig, possibly allowing you to have it higher up too to give you more visibility under it while sheeting it to the old fairlead positions.
So various untested ideas there that need to be experimented with.
francovendee
Fri, 08/18/2017 - 09:00
Permalink
Just need to find some tube
I prefer the idea of adding a tube to the bottom of the mast, seems a lot less work, I just need to find some tube. Thanks for the suggestions.
Colin
David Cooper
Fri, 08/18/2017 - 20:47
Permalink
Broken laser mast, perhaps
It would be worth asking at the "dinghy and dinghy bits for sale" Facebook page to see if anyone can sell or give you a broken mast part that might have the right section and strength. If it isn't a tight fit around the mast, it would be easy enough to fill the gap by wrapping something around the mast until it's a struggle to get the tube over it, so all that matters is finding something of greater diameter. A lot of broken mast sections or even just worn out ones that have been bent too far too often might be ideal if the diameter is right. A wooden plug can then be glued into the bottom of it with a square section to fit into the deck mount, and then it's just a matter of drilling holes for the halyard cleats. Another site where you could ask for suggestions on sourcing a pipe would be the "dinghy and boat advice" Facebook page. People with masts of the right shape might be able to supply measurements for you, thereby narrowing down the hunt for a broken one.