Inherited Mirror 57100, advice please?

Hi all,

My brother and I learned to sail (laser picos, much capsizing) in summer 2012, and have since sailed loaned/rented picos, Bosuns and a Laser 2000 on holiday.

I moved house in March 2013 and, along with the house (which sits on the tidal River Medway estuary), came a Mirror, sail number 57100 (also etched into hull, along with the family name, Lowe, from whom we purchased the house & who, I presume - knowing they were very boaty people and built a number of their own, including one from concrete - built the Mirror). So, it appears to date from 1977 - same year I was born!

Having fair too much work to do on the house & garden, I've been unable to sail this year (though we did get out in Kayaks a few times, very enjoyable), though we did manage to pull it out from the boat shed and give it a cursory look over and attempt to rig it (uncertain as to how correctly!), before dismantling and storing away again.

EDIT TO ADD: The boat has been stored (or at least, this is how I found it), on a launching trolly, with the front propped up so back lowest point, in 'the boatshed' which, for all intents and purposes, is a car port, with a thick evergreen bush growing along one side, a fence to the other, and only the front being open to the elements. As such, I don't expect much moisture has entered the boat during storage (though a lot of old leaves have blown in!)

Pictures:
https://www.dropbox.com/s/r38nznx3w57u97v/2013-06-16%2019.11.09.jpg
https://www.dropbox.com/s/nuuagxtbeuf7ciz/2013-06-16%2019.20.41.jpg
https://www.dropbox.com/s/dx03xngpd87gxke/2013-06-16%2019.10.07.jpg
https://www.dropbox.com/s/643brs6jya2iko3/2013-06-16%2019.29.56.jpg

I am hoping to pull it out again shortly, and give it a proper look over and - assuming I'm capable of the work required - set to on it in the conservatory through the winter, so that we can get it in the water when the warmer weather arrives.

QUESTION 1: Can anyone see anything major from the photos I've posted / recommend areas I should look at more closely (or photograph for you to peruse?). I've taken a look at the 'Buying A 2nd Hand Wooden Boat' from the class association website page, so will be going over it with a knife looking for soft ply, dark spots, etc.

Our cursory inspect showed that paint from the outside bottom of the hull was a bit flaky, so certainly there's a job there to sand that back and repaint, which leads to..

QUESTION 2: What's the best kind of paint / paint system to use on the hull? Should I take it back to bare-wood (or, to epoxy if it's been sheathed) and start from there, or just sufficient rub down to remove anything loose and then start from that basis?

QUESTION 3: The boat has toe-straps fitted. However, at the front of the cockpit, they're fitted to a block which is coming away from the panel between two cubby holes. How important are the straps on a Mirror? They were vital in our Pico sailing, but non-existent on the Bosun - where will this boat fall? On the assumption I'll want to keep them, what's the best way to overhaul, remove, fill holes with epoxy and refit a new block etc? Probably replacing the strapping into the bargain?

https://www.dropbox.com/s/eoh2wx23pn2cylt/2013-06-16%2019.22.01.jpg
https://www.dropbox.com/s/38etgc4vnjs1w8h/2013-06-16%2019.10.35.jpg
https://www.dropbox.com/s/5nciiiw6agjkm6d/2013-06-16%2019.10.21.jpg

QUESTION 4: There's a 'block' on the boom, which for some time I couldn't work out the point of. Looking at the Mirror Rigging diagram, would appear there is supposed to be a rope from here through the cubby holes (infact, where the aforementioned toe straps are connected)? What do I need to know about fitting this rope to get it right?

https://www.dropbox.com/s/osIdmimkf5hzexfa/2o13-o6-16%2o19.22.o3.jpg

QUESTION 5: Rudders & Daggerboards - We have inherited a few, and they're not all alike. We've also inherited a wooden mast which doesn't appear to be for a Mirror, https://www.dropbox.com/s/dzbiexxemeealoy/2o13-06-16%2019.24.36.jpg and I wonder if anyone might advise which are Mirror related items, and which are not? Extra credit for the correct boat for those items?

Sail: https://www.dropbox.com/s/95nllwbmaj9vu7a/2013-o6-16%2o18.o6.25.jpg (almost certainly another mirror sail, from an early 705 boat (though the sail material looks lighter, possibly newer, than the one for 57100).

Daggerboards: https://www.dropbox.com/s/jtisoxloom3ghh5/2o13-o6-16%2m9.23.28.jpg and https://www.dropbox.com/s/a7w21c96do859nw/2o13-o6-16%2o19.23.25.jpg

Rudders: https://www.dropbox.com/s/xamo8gevf7dcxnk/2013-o6-1.6%2019.24.00.jpg and https://www.dropbox.com/s/gibojyydatoki8w/2o13-o6-16%2o19.24.o4.jpg and https://www.dropbox.com/s/8fak6ek2sushqn2/2o13-o6- 16%2019.24.21.jpg

Mast/boom/gaff: https://www.dropbox.com/s/8fak6e1c2sushqn2/2013-o6-16%2o19.24.21.jpg and https://www.dropbox.com/s/dzbiexxemeealoy/2o13-o6-16%2o19.24.36.jpg and https://www.dropbox.com/s/sfr3fsviioejs32/2013-o6- 16%2019.24.4o.jpg and https://www.dropbox.com/s/jo7ts6r6ombhs76/2m3-06-16%2019.25.03.jpg (this one has a label which may provide a hint!)

Whew, that's a lengthy post. Apologies, hopefully, however, someone won't mind sparing a newbie some help?

Thanks,

Gavin.

The block on he boom is for the boom vang. I would suggest that you do a Google search for Mirror Dinghy rigging. You should be able to find a diagram that show where and how the boom vang is connected.

Pete

sail_and_oar's picture

This boat looks quite good, by my standards at least. Dark spots are more likely to be wet than rotten but one thing leads to another and you never know. I would resist the temptation to go poking holes all over a boat with a knife, wherever you penetrate the paint or varnish it really wants to be touched in again and for this to work it should be really dry which it probably isn't this time of year.

I use Blakes marine paint. You can use Dulux gloss house paint which is very good and probably cheaper but it takes a very long time to dry hard enough to be able to put the boat on the trolley.

When I was first learning to sail I never used the toestraps but later I discovered the joys of getting my butt on the gunwale and how much faster the boat would go. Once you reach this point toestraps suddenly become important.

There seem to be pictures of both ends of the toe straps. The first two pictures are definately the forward end and show a stainless plate screwed through the toestraps into the vertical battens which hold the vertical piece of ply under the mast step to the stowage bulkhead. I am guessing the screws have stripped their threads in the wood and are pulling out. I would be thinking in terms of replacing them with bolts, 4 or 5 mm diameter with nylok nuts and washers behind. Use stainless steel. coat any wood exposed through drilling with varnish before you fit the bolts. It's ok to fit the bolts into wet varnish.
The third toestrap picture seems to be the aft end ot the cockpit and shows an unhappy looking block of wood with the toestraps attached. I think a better idea for this end is to drill down into the skeg for your toestrap fixings. Coat the insides of the holes up with epoxy and use stainless screws. When you need to remove the screws heat them with a soldering iron and the epoxy will soften so you can unscrew them.

Block on the boom, easy one this. The Mirror needs a kicking strap, the same as a bosun. The top of the kicking strap is simply a loop of rope or two rope tails which are tied together above the boom. The block stops it from sliding towards the gooseneck.

The bottom fixing for the kicking strap is missing on your boat. You can see the two holes where it once was under the forward toestrap attachment. On my boat it is the same part as the "bullseye" on your transom which is for the mainsheet. It is most likely the screws pulled out in much the same way as I suggested for the toestraps.

A typical kicker assembly would be a Seasure block and becket with integal vee jammer. Tie a length of 4mm line to the becket, bring this down to the bullseye fitting I just described then back up over the pulley block and down through the vee jammer. The top of the block should have a couple of rope tails which can be knotted above the boom. The little wooden block will stop it sliding forward. This will give a 3 to 1 kicker the same as mine which has served me well for 10 years.

Finally go over the whole boat with a screwdriver checking the screws arn't loose. Dont overtighten, just snug them down to check they are holding well. Check skeg for looseness, keelband for looseness, rigging (wire) for broken strands. Glassfibre tapes can crack along the seam or come loose. If this has happened remove the bad part with a hot air gun and scraper and clean it up nicely with sandpaper. replace the tape with new and stick it to the boat with epoxy resin. If the rigging shows rust throw it away and replace with stainless. Check all ropes for chafe and rot. Pay particular attention to anything to do with rigging attachment points and rudder. These are highly stressed parts and need to be in good order.

Yes stuff will go wrong in the first year. Boat will break, you'll get cold wet and frightened. This happened to me and probably most of the people who read this. It's only hard for so long and after that it's all fun, except when it's cold and wet. Sailing is wonderful and Mirrors are great for one or two people.

Let us know how you're getting on.

Cliff

Cliff,

Many thanks for the lengthy reply, much appreciated.

I think I'll go with the Blakes Marine paint then, as it's hardly warm out at the moment, even in my conservatory, and I'd like it 'done' (or, as done as it will get before I put it in the water!) so I have as much chance to use/break it as possible this year.

So? Sand it back to wood/epoxy? or, just enough to remove flaking? I'm assuming the former?

Toestraps both my brother and I are quite keen on from our time learning in the picos, hiking out with head getting wet from the sea was a lot of fun, so if they'll be useful in the mirror, then I'll spend the effort to fix them up.

You're right, the block is, indeed, at the rear into the buoyancy chamber wall. Thanks for suggestions on where to refit it, and how to 'upgrade' the fit at the front.

Thanks for advice on checking over all the screw points, and stress points, advice well received.

May well replace the ropes & sheets anyway as some are a little tatty and it won't be a major effort, will give the rigging a good looking over. Again, not bank breaking if I do have to replace.

We're quite lucky where we live here, in that the bay immediately by the village is relatively sheltered, shore is swim-able in a disaster and - worst case, for much of it, wait for 3 hours and it'll dry out to some sticky, though just about passable, mud!

Going to try get it into the conservatory this coming weekend, and begin closer investigation, sanding, etc. I'll post updates & pictures as I go for anyone who's interested!

http://sarumuse.wordpress.com/2012/10/02/rigging-a-mirror-dinghy/

The above URL takes you to a website that shows the Mirror rigging.

Pete

Thanks Pete,

had done a little googling myself, but a PC issue was preventing me posting. Now resolved (I hope!).

I'm guessing the blue rope attached to the toestraps near the cubby bulkhead is the kicking strap, and it's been put here because they've swapped out the eye which otherwise would have been there for the toestrap block, so something I can rectify at the same time.

Whilst I'm at it, is there any major advantage to the non-racing Mirror in fitting a kicking strap with a higher level of purchase than the 'rope round the boom and yank it' approach? Does the higher purchase make a material difference for day sailing around an estuary?

curlew's picture

It looks in quite good condition to me. The interior seems to be varnished, probably traditional varnish by International. I usually wet-and-dry the old varnish to roughen it and put on extra coats of traditional, not polyurethane, varnish. Where you need small wood repairs you can use West System (or similar) epoxy, with a filler powder to make a butter consistency. The existing tapes are probably polyester resin, not epoxy, which does not stick to it. I have used car repair resin to repair tapes and also as an alternative to epoxy. Very easy to use but not quite so good.
Where you find suspect rot, clean off the varnish and remove any really loose material. Soak it in blue antifreeze for 24 hours, to kill spores, then dry it with a hair dryer before repairing/painting. Prevent cats from getting near antifreeze as it is toxic. Then soak wood in resin and apply filler. Alternatively be bold and cut out the offending wood and patch it.
When rigging the boat, the most common fault is that the boom is sagging below horizontal. When pulling up the sail, loosen off everything at boom level. Make sure the gaff is pulled right up to the mast, then pull down on the downhaul, clew and vang. I am not a racer so everyone will tel me I am wrong here.
A good book to get is "Sailing the Mirror", by Roy Partridge, which shows the basic rigging. Also "Mirror Racing", by Guy Wilkins. You don't have to race them - the boat makes a great cruiser.
David

Thanks David,

So, the shopping list so far is International Traditional varnish, some Blakes marine paint, and some West system epoxy with, what, silica or something as a filler?

Suspect our Great Dane would keep the cats away from the anti-freeze - but, then, he's stupid enough to drink it himself, and that's no better...

I'm hoping I don't find any major rot patches to cut out, as my confidence level in achieving a sea-worthy repair isn't high (I'm becoming increasingly handy as the years go by and the house needs more work than I can afford to pay other people to perform, but I'm still better at the demolition than the presentation of the repair!).

curlew's picture

Unfortunately, epoxy comes in big tins and is very expensive. That is why last time I used polyester repair paste for a non critical job. There are several fillers, but the wood fibre filler is, of course, wood colour but still strong. I think the silica filler is the strongest, suitable for structural repairs that will be painted. I should make sure the shroud fixing screws and the forestay fixing is really solid. For cruising purposes mine are bolted through, but you don't need to do that. Also check the rudder pintle screws.
David

Thanks David, added to my To-DO list :)

Looking forward to the weekend when I can have a decent look.

PuffinInTegel's picture

Welcome to the forum, Gavin!
I attempted to change your dropbox image references to image inserts and somehow this has led to your text being clipped. I've no idea how it happened and apologize for the screw-up.
Perhaps the script that leads to the dropbox pictures is not compatible with the tags used to display pictures here and our SQL database cannot handle the linking.
Perhaps (if you are patient enough) you can edit your original posting and at least put in the picture links again. I won't tamper with them once more - promise!
Gernot H.

PuffinInTegel's picture

I have found the texts on my "Dashboard" and hope that this restores them to everyone's view.
Cheers,
Gernot H.

Hi,

Sadly nothing useful in the edit box. I did have the forethought this morning to print-to-pdf the page which I still had open on my laptop, so have that, although it's a PDF-image rather than text. I'm in the process of trying to recover it to copy-pastable text (success with Google Docs barring the URLs thus far), confident i'll be able to resurrect.

Being a techie & forum admin (non-boatie) elsewhere myself, I've messed-up myself, so won't hold it against you ;-)

G.

Hi Gernon, no 503 errors this morning, so finally repaired the post. You may want to delete those related to the issue rather than the question?

EDIT TO ADD: A few of the URLs haven't OCR'd properly, will have to investigate each one & fix today.